gonzopi

git clone https://git.tarina.org/gonzopi
Log | Files | Refs | README | LICENSE

rpi4_boot_config (2912B)

      1 # For more options and information see
      2 # http://rpf.io/configtxt
      3 # Some settings may impact device functionality. See link above for details
      4 
      5 # uncomment if you get no picture on HDMI for a default "safe" mode
      6 #hdmi_safe=1
      7 
      8 # uncomment this if your display has a black border of unused pixels visible
      9 # and your display can output without overscan
     10 #disable_overscan=1
     11 
     12 # uncomment the following to adjust overscan. Use positive numbers if console
     13 # goes off screen, and negative if there is too much border
     14 #overscan_left=16
     15 #overscan_right=16
     16 #overscan_top=16
     17 #overscan_bottom=16
     18 
     19 # uncomment to force a console size. By default it will be display's size minus
     20 # overscan.
     21 #framebuffer_width=1280
     22 #framebuffer_height=720
     23 
     24 # uncomment if hdmi display is not detected and composite is being output
     25 #hdmi_force_hotplug=1
     26 
     27 # uncomment to force a specific HDMI mode (this will force VGA)
     28 #hdmi_group=1
     29 #hdmi_mode=1
     30 
     31 # uncomment to force a HDMI mode rather than DVI. This can make audio work in
     32 # DMT (computer monitor) modes
     33 #hdmi_drive=2
     34 
     35 # uncomment to increase signal to HDMI, if you have interference, blanking, or
     36 # no display
     37 #config_hdmi_boost=4
     38 
     39 # uncomment for composite PAL
     40 #sdtv_mode=2
     41 
     42 #uncomment to overclock the arm. 700 MHz is the default.
     43 #arm_freq=800
     44 
     45 # Uncomment some or all of these to enable the optional hardware interfaces
     46 dtparam=i2c_arm=on
     47 #dtparam=i2s=on
     48 dtparam=spi=off
     49 
     50 # Uncomment this to enable infrared communication.
     51 #dtoverlay=gpio-ir,gpio_pin=17
     52 #dtoverlay=gpio-ir-tx,gpio_pin=18
     53 
     54 # Additional overlays and parameters are documented /boot/overlays/README
     55 
     56 # Enable audio (loads snd_bcm2835)
     57 #dtparam=audio=on
     58 
     59 [pi4]
     60 # Enable DRM VC4 V3D driver on top of the dispmanx display stack
     61 #dtoverlay=vc4-fkms-v3d
     62 #max_framebuffers=3
     63 
     64 [all]
     65 #dtoverlay=vc4-fkms-v3d
     66 
     67 #-----GonzoPi configuration starts here-------
     68 
     69 [edid=HDMI-A-2]
     70 hdmi_enable=1
     71 max_framebuffers=2
     72 disable_overscan=1
     73 hdmi_force_hotplug:1=1
     74 hdmi_group=:1=1
     75 hdmi_mode:1=82
     76 hdmi_blanking=1
     77 
     78 [all]
     79 #dtoverlay=vc4-fkms-v3d
     80 
     81 #gonzopi-rpi-configuration-hyperpixel-1.0
     82 #hyperpixel
     83 enable_dpi_lcd=1
     84 #display_lcd_rotate=1
     85 start_x=1
     86 gpu_mem=512
     87 disable_splash=1
     88 force_turbo=1
     89 boot_delay=1
     90 # dtparam=sd_overclock=90
     91 # Disable the ACT LED.
     92 dtparam=act_led_trigger=none
     93 dtparam=act_led_activelow=off
     94 # Disable the PWR LED.
     95 dtparam=pwr_led_trigger=none
     96 dtparam=pwr_led_activelow=off
     97 #hdmi_force_hotplug=1
     98 #hdmi_group=1
     99 #hdmi_mode=16
    100 #hdmi_port=2
    101 #hdmi_blanking=1
    102 
    103 #[edid=Ras-LCD Panel]
    104 dtoverlay=hyperpixel4
    105 #display_auto_detect=0
    106 #display_default_lcd=0
    107 framebuffer_width=800
    108 framebuffer_height=480
    109 overscan_left=0
    110 overscan_right=0
    111 overscan_top=0
    112 overscan_bottom=0
    113 enable_dpi_lcd=1
    114 display_default_lcd=1
    115 dpi_group=2
    116 hdmi_group=3
    117 dpi_mode=87
    118 dpi_output_format=0x7f216
    119 hdmi_timings=480 0 10 16 59 800 0 15 113 15 0 0 0 60 0 32000000 6
    120 #hdmi_force_hotplug:1=1
    121 #hdmi_group:1=2
    122 #hdmi_mode:1=10
    123 
    124 #--------GonzoPi configuration end here---------
    125 
    126